Use of sampling techniques in fieldwork

• Sampling is a method of investigating the?abundance and distribution of species and populations
• There are two different types of sampling:
  • Random
  • Non-random

   

• In random sampling, the positions of the?sampling points?are completely random or?due to chance
• In non-random sampling, the positions of the?sampling points are chosen?by the person carrying out the sampling
• There is a range of different sampling equipment which can be used:
  • Quadrats
  • Sweeping nets
  • Pitfall traps
  • Pooters
  • Tullgren funnel

   

The quadrat method of sampling

Apparatus

• Quadrat
• Random number generator

Method for choosing sample sites

• Mark up a grid on a map or a to-scale drawing of the area being studied and label the grid with coordinates
  • It is important that the area is big enough to get a representative estimate for the specific habitat/ecosystem

   

• Use a?random number generator?to choose a?set of coordinates
  • This is done to?avoid sampling bias?which could lead to over or under-estimation (either subconsciously choosing areas that are easier to access or that look like they contain individuals)

   

Getting measurements from quadrats

• The contents within quadrats can be counted using different measurements
• Population density, percentage cover and species frequency are all different ways of counting and recording the number of different species and individuals present within a quadrat

Calculating population density (number of individuals per m---2):

• Place a quadrat at the generated coordinate
• Count the?number of individuals?in each quadrat
• Use a?running mean?to determine the number of quadrats required to get a representative sample:
  • Calculate the mean number of individuals per quadrat for the first two quadrats found, then the mean of the first three, then the mean of the first four and repeat until there is no further significant change in the mean

   

• To calculate the?estimated population size?for the whole area or habitat,?divide the whole area by the area of one quadrant, then multiply this value by the?mean number of individuals per quadrat

Calculating the abundance of a species using percentage cover (%):

• Usually used for?plants
• Place a grid quadrat (a square frame split into 100 smaller squares) at this coordinate
  • Each square of a grid quadrat is equivalent to?1% cover

   

• Count the number of squares in each quadrat within which the species occupies?over half the square
  • If?30 squares?contain the species, the percentage cover is?30%
  • This method is?subjective?and therefore the?same person?should make the estimate for?all samples?to control this variable

   

Calculating the abundance of a species using frequency (%):

• Place a frame quadrat at multiple coordinates generated
• Count the number of quadrats that contain the species
  • If 3 out of 10 quadrats contain the species the frequency is 30%

   

Interpreting results from quadrats

• The results from the quadrats can be used to calculate the predicted frequency and density of a species within an area
• Species density?indicates how many individuals of that species there are per unit area
  • The number of individuals counted across all?quadrats?is divided by the total area of all the quadrats
  • For example, if 107 bluebells were found across 50 quadrats that are 1m2?each the species density would be 107/50 = 2.14 individuals per m2

   

• It can sometimes be difficult to count individual plants or organisms. When this is the case?percentage cover?of the species within the quadrat can be estimated instead
  • The quadrat is divided into 100 smaller squares. The number of squares the species is found in is equivalent to its percentage cover in that quadrat
  • For example, if grass is found in 89 out of 100 squares in the quadrat then it has a percentage cover of 89%

   

• Species frequency?is the probability that the species will be found within any quadrat in the sample area
  • The number of?quadrats?that the species was present in is divided by the total number of quadrats and then multiplied by 100
  • For example, if bluebells were found in 18 out of 50 quadrats the species frequency would be (18/50) x 100 = 36%

   

How to estimate percentage cover of one or more species using a quadrat

Limitations of using quadrats

• Quadrats and transects can only be used for?sessile and immobile species?(eg. plants and slow-moving animals)
• Some species can be counted to find their abundance but others that are very small or in high numbers require abundance to be calculated using percentage cover or frequency techniques
  • The frequency technique shows how common a species is but it does not give information on the estimated number of individuals or the size of the population

   

• Percentage cover and frequency, when used together, give a good picture of the?distribution of a species
  • If a species had a high mean percentage cover but a low frequency it would suggest the species lives in groups in preferred areas of the habitat
  • This can be used to answer questions such as: does the species prefer light or dark and wet or dry areas etc.

   

The mark-release-capture method of sampling (estimating population sizes of mobile animals)

• The sampling method described above is only useful for?non-motile?(sessile) organisms
• Different methods are required for estimating the number of individuals in a population of?motile animals
  • The?mark-release-capture?method is used

   

• For a single species in the area:
  • The?first large sample is taken. As many individuals as possible are caught, counted and?marked?in a way that won’t affect their survival e.g. if studying a species of beetle, a small amount of brightly coloured non-toxic paint can be applied to their carapace (shell)
  • The marked individuals are?returned to their habitat?and allowed to randomly mix with the rest of the population
  • When a sufficient amount of time has passed?another large sample is captured
  • The number of marked and unmarked individuals within the sample are?counted
  • The proportion of marked to unmarked individuals is used to calculate an?estimate of the population size
  • The formula for the calculation is:

   

N = (n1?× n2) ÷ m2

• • Where:
    • N?= population estimate
    • n1?= number of marked individuals released
    • n2?= number of individuals in the second sample (marked and unmarked)
    • m2?= number of marked individuals in the second sample

     

Step One: Write out the equation and substitute in the known values

N = (n1?× n2) ÷ m2

N = (236 × 244) ÷ 71

Step Two: Calculate the population size estimate (N)

N = 57,584 ÷ 71

N = 811

Results from mark-release-capture

• When using the mark-release-capture method, there are a few?assumptions?that have to be made:
  • The marked individuals are given?sufficient time?to?disperse?and?mix?back in fully with the?main population
  • The marking doesn't affect the?survival rates?of the marked individuals (e.g. doesn't make them more visible and therefore more likely to be predated)
  • The marking remains?visible?throughout the sampling and doesn't rub off
  • The?population?stays the?same size?during the study period (i.e. there are no significant changes in population size due to births, deaths or migrations into or out of the main population)